American DJ Flat Par Tri18X User Manual download pdf (Page 4)

©American DJ® - www.Americandj.com - Flat Par Tri18 User Manual Page 8

Flat Par Tri18 Operating Instructions

©American DJ® - www.Americandj.com - Flat Par Tri18 User Manual Page 7

LED Display On/Off:

To set the LED display to turn off after 10 seconds, press the MODE but-

ton until “don” is displayed, press the UP button to display “doff”. Now

the display will disappear after 10s. Press any button to turn the display

on again. Be advised though that the display will turn off automatically

after 10 seconds.

To set the display press the MODE button until “dXX” is displayed. Use

the UP or DOWN buttons to select either:

“don” = LED display on at all times.

“doFF” = LED display shuts off after 10 seconds.

Operating Modes:

You can use the Flat Par Tri18 in five ways:

• Sound-Active mode - The unit will react to sound, chasing through the

built in programs.

• Static Color Mode - There are 7 colors to choose from.

• Auto Mode - There are 3 Auto Modes to choose from.

• RGB Mode - Choose one of the three colors to remain static or

adjust the intensity of each color to make your desired color.

• DMX control mode - This function will allow you to control each

individual fixtures traits with a standard DMX 512 controller such as

as the American DJ® Show Designer™.

Master-Slave Operation:

This function will allows you to link units together to run in a Master-

Slave mode. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units built-in programs.

Any unit can act as a Master or as a Slave however, only one unit can be

programmed to act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of the unit.

Use standard XLR microphone cables to link your units together.

Remember that the Male XLR connector is the input and the Female

XLR connector is the ouput. The first unit in the chain (master) will

use the female XLR connector only. The last unit in the chain will use

the male XLR connector only.

2. Connect the rst “Slave” unit to the “Master.”

3. Set the “Master” unit to your desired mode of operation. The “Slave”

unit will now follow the “Master”.

Sound Active Mode:

In this mode the Flat Par Tri18 will react to sound, and chase through the

different colors.

1. Plug the fixture in and press the MODE button until “So-X” is dis-

played. “X” represents the sound active mode (1-8) currently dis-

played.

2. The fixture will now change via sound.

3. Press the SET UP button to adjust the sound sensitivity. “SJ-X”

should be displayed. Use the UP or DOWN buttons to adjust the sen-

sitivity. “SJ-1” is the lowest sensitivity, “SJ-8” is the highest.

Static Color Mode:

1. Plug the fixture in and press the MODE button until “CL-X” is dis-

played.

2. There are 7 colors to choose from. Select your desired color by

pressing the UP and DOWN buttons. After you have selected your

desired color you can activate strobing by pressing the SET UP but-

ton to enter the Flash (strobe) mode.

3. “FS.XX” will be displayed, this is Flash mode. The Flash can be

adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

Auto Mode: There are 3 types of Auto Modes to choose from; Color

Fade, Color Change, and both modes running together.

The running

speed is adjustable in all 3 modes.

1. Plug the fixture in and press the MODE button until either “AF-X”,

“AJ-X”, or “A-JF” is displayed.

• AF-X = Color Fade mode, there are 8 Color Fade modes to choose

from. Use the UP or DOWN buttons to scroll through the different

Auto Fade modes.

• AJ-X = Color Change mode, there are 8 Color Change modes to

choose from. Use the UP or DOWN buttons to scroll through the

different Auto Change modes.

• A-JF = Both Color Fade and Color Change modes running.

2. After you have chosen your desired running mode press the SET UP

button until “SP.XX” is displayed. When this is displayed you can

adjust the running speed of your desired program. Use the UP or

DOWN button to adjust the speed between “SP.01” (slowest) and

“SP.16” (fastest). Once you have set your desired running speed,

press the SET UP button to return to your desired Auto Mode.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

American DJ Flat Par Tri18X User Manual Page 4

Comments to this Manuals

Related products and manuals for DJ controllers American DJ Flat Par Tri18X